ENIT

F.A.Q.

PROCEDURE models only EASY METER and EASY METER T2

Through the instrument keyboard can be created directly in the instrument, the MEMORY MANUAL PLANS, for example MANU 2, MANU 3, etc.  containing (QAM) CATV channels interest you.

IMPORTANT:
The channels created in the MANUAL memory plan (eg MANU 2), are NOT added in the plan MASTER. After you created, for recall, press CATV, then the key PLAN, select the item MANUMEMORY (MIX) and select the number of MANUAL memory plan desired (eg Figure A)
.
 
ROVER_Series_MANU_2
Figure A: Select a MANUAL memory plan (eg MANU 2)

P
REREQUISITES: To create a manual memory, you must know all the data for each channel (QAM) CATV (DVB-C) to be stored: Channel / Frequency, Symbol Rate, Constellation.
 
PROCEDURE:
1. Turn on the instrument,
2. Make sure you've selected your language of your interest,
3. Press the "CATV" key,
4. Press the "PLAN" key,
5. Rotate the encoder (ENTER) and select the word "MASTER" (Figure 1),
6. Press the encoder (ENTER) to confirm,
7. Rotate the encoder (ENTER) and select your country, for example "EUROPE" (Figure 1),
8. Press the encoder (ENTER) to confirm,
9. Rotate the encoder (ENTER) and select the icon "MEMORY" (Figure 1),
 
ROVER_Series_MASTER_EUROPE_MEMORY
Figure 1: Sequence selection "MASTER",
"EUROPE" and "MEMORY"
 
10. Press the encoder (ENTER) to confirm,
11. Rotate the encoder (ENTER) and select the word "MANUMEMORY" (Figure 2),
12. Press the encoder (ENTER) to confirm,
13. Press again the encoder (ENTER),
14. Rotate the encoder (ENTER) and select a "PLAN" memory manual of your choice: for example, if free "MANU 2" (Figure 2 ) up to 10,
15. Press the encoder (ENTER) to confirm,
16. Rotate the encoder (ENTER) and select the word "START EDIT" (Figure 2),
 
ROVER_Series_MANUMEMORY_START_EDIT
Figure 2: Sequence selection "MANUMEMORY",
"PLAN" and "START EDIT"
 
17. Press the encoder (ENTER) to confirm,
18. Press again the encoder (ENTER),
19. Rotate the encoder (ENTER) and select the word "MODIFY ITEM" (Figure 3),
 
ROVER_Series_MANUMEMORY_EDITING_ACTION_MODIFY_ITEM
Figure 3: Selectng written "MODIFY ITEM"
 
20. Press the encoder (ENTER) to confirm,
21. Rotate the encoder (ENTER) and select the word "MODE" (Figure 4),
22. Press the encoder (ENTER) to confirm,
23. Rotate the encoder (ENTER) and select the word "DVB-C" (Figure 4),
24. Press the encoder (ENTER) to confirm,
 
NOTE:
  • If you know the CHANNEL to be stored do the following,
  • Otherwise, if you only know the center frequency, continue from step 29,

25.
Rotate the encoder (ENTER) and select the word "CHAN" (Figure 4),
26. Press the encoder (ENTER) to confirm,
27. Rotate the encoder (ENTER) and select the desired channel (eg s19) (Figure 4),
28. Press the encoder (ENTER) to confirm,
29. Rotate the encoder (ENTER) and select the word "FREQ" (frequency MHz) (Figure 4),
30. Press the encoder (ENTER) to confirm,
31. Rotate the encoder (ENTER) and set the desired frequency, or hold 2 second encoder (ENTER) and enter directly the value of frequency using the numeric keypad (for example, 290.00 MHz). If necessary, rotate the wheel ' encoder (ENTER) to move between numbers,
32. Press the encoder (ENTER) to confirm,
33. Rotate the encoder (ENTER) and select the word "SYM.RATE" (Symbol Rate) (Figure 4),
34. Press the encoder (ENTER) to confirm,
35. Rotate the encoder (ENTER) and sets the value of symbol rate you want, or hold 2  second encoder (ENTER) and enter directly the value of Symbol Rate by using the numeric keypad (eg 5156 Ms / s). If necessary, the encoder wheel (ENTER) to move between the numbers (Figure 4),
36. Press the encoder (ENTER) to confirm,
37. Rotate the encoder (ENTER) and select the word "CONST" (constellation) (Figure 4),
38. Press the encoder (ENTER) to confirm,
39. Rotate the encoder (ENTER) and sets the value of the desired constellation (eg QAM256),
40. Press the encoder (ENTER) to confirm,
41. Rotate the encoder (ENTER) and select the "SAVE?" (Figure 4),
42. Press the encoder (ENTER) to confirm.
 
ROVER_Series_ITEM_EDITING_SAVE
Figure 4: Selection of all parameters and "SAVE?"
 
The channel (QAM) CATV (in our example s19) is successfully saved in the MEMORY MANUAL selected (in our example MANU 2) (Figure 5),
 
ROVER_Series_ACTION_MANUMEMORY_EDITING
Figure 5: Memory created
 
If you want to add a new channel in the same MANUAL MEMORY, select the word "ADD BELOW" to add a new channel below (Figure 6) and proceed as indicated from paragraph 20,
 
ROVER_Series_ACTION_ADD_BELOW
Figure 6: Select the "ADD BELOW"
 
Or, select the text "ADD ABOVE" to add a new channel below (Figure 7) and proceed as indicated in paragraph 20,
 
ROVER_Series_ACTION_ADD_ABOVE
Figure 7: Selecting "ADD ABOVE"
 
If you want to change the frequency entered, select the word "MODIFY ITEM" (Figure 8) and proceed as indicated in paragraph 20,
 
ROVER_Series_ACTION_MODIFY_ITEM
Figure 8: Selecting written "MODIFY ITEM"
 
If you want to cancel the frequency entered, select the word "DELETE ITEM" (Figure 9).
 
ROVER_Series_ACTION_DELETE_ITEM
Figure 9: Selecting word "DELETE ITEM"
 
The MENU (written and graphic) of the figures shown in the following "F.A.Q.", may vary from model to model and without notice.